Lowrance Structurescan Lss 1 Wiring Diagram

Looking at the wiring diagram for a LSS1 showsRed- hot wireBlack- I just purchaed the same setup as you 2-hds8s with structure scan. Lowrance Structurescan Wiring Diagram.

Lowrance Structurescan Lss 1 Wiring Diagram - If you're looking for picture and video information linked to the keyword you have come to visit the ideal site. Our site provides you with hints for seeing the maximum quality video and image content, hunt and find more enlightening video content and graphics that fit your interests. comprises one of tens of thousands of movie collections from various sources, particularly Youtube, so we recommend this video for you to see. This site is for them to stop by this site.

Simrad Structurescan Lss 1 Sonar Module Specification Manualzz

The yellow accessory wake-up wire from the HDS can be directly connected to the yellow wire on the LSS-1 instead of a separate switch.

Lowrance structurescan lss 1 wiring diagram. There are two ground pins with unclear function. I need a wiring diagram for how the nmea2000 bus should be connected for an e tec 150 I have installed a new HDS10 with structure scan and. The ground - black lead to a ground tab on a common connector block and the red power lead to a tab on the ACC console switch.

I performed a reset on my HDS 10 gen 1 and now StructureScan doesnt show up at all on pages. This video is part of 1 of a 3-part series that provides guidance on installing a Lowrance StructureScan 3D HDS-12 Gen 3 locators a SpotlightScan and Point. I just purchased a HDS 8 gen 2 with the structure scan bundle and am now moving the HDS 7 to the bow and planning on the 8 being on.

Im a Lowrance user and have the HDS 7 Gen 2 LSS-1 module and the LSS-2 transducer and the 50200 transducer as well. 4 high definition screen of the hds- 8. The yellow wire turns it On or Off I guess it works just like a relay.

Console boat with a bow mount trolling motor. I have indicated the function of the pins in the image. Two stainless steel screws will mount in about 12 inches up on the back wall back side of the rod locker.

Depending on your budget you can go up from a 3 screen all the way to a 9 screen. You can get DownScan CHIRP and GPS in this series these are a user friendly units basically a plug-n-play and go fishing units. This diagram on page 11 shows a switch that does not come with the unit to be installed inline with the yellow wire.

If you decide to use a switch just cap and. SIMRAD LSS-1 StructureScan Module with Power Cable and Mounting Hardware Simrad Model Number. The LSS-1 will be located directly under the drivers console.

1 on the bow and one at the console. LSS-1 module ethernet cable StructureScan transducer transducer mounting. With this technology you will be able to lowrance lss 1 structurescan manual see what is below the boat as an image with amazing detail on the large 8.

This boater wants 2 sonars and. 000-10238-001 The Simrad LSS-1 StructureScan unit is a black box module designed to connect either direct to Simrad NSE NSO and similar multifunction displays or to a wider integrated Simrad navigation network. Turning on the HDS then turns on the LSS-1.

Drill the pilot holes. Websites under the StructureScan 3D Transducer documentation section. Here is where the Lowrance Elite series excels.

The LSS-1 unit needs the yellow wire connected to power and the information is on page 11 of the StructureScan installation proceedures. LSS-1 Simrad Part Number. I connected the yellow wire from the HDS-10 to the LSS-1.

My ranger came with 2 520cs. I run sonar in split screen with seperate 50200khz sonar screens along with a sidescan or downscan view either 455 or 800khz of structure which also shows fish arches in the downscan view. One could be ground for temp and the other is probably a shield ground.

And fuse holder StructureScan transducer mounting. An in-line fuse installed in the red power lead. One thing I missed as being clear from the manuals.

Many like the separate switch though. The StructureScan doesnt have an onoff switch so you need to decide how to power it. Lss-1 power led is on sonar led blinking.

When I power up the HDS-10 it turns on the LSS-1. If the 20 transducer cable is not long enough a 10 extension cable is available part number. Your StructureScan box is packed with the LSS-1 black box a Power cable fuse.

I replaced the one at the console with a HDS 7 and had the local Tackel Shop install it for me. I will be installing Structurescan on my Ranger boat. Cable wiring diagram in your HDS Installation manual for more information.

Your method would work if you want to use the main disconnect as the switch. LSS-1 from the desired transducer mounting location. Installation instructions for your accessory and accessory pack content tables on the.

Hey guys just hoping someone might be able to point me in the right direction for a wiring diagram. You have the choice to have it power up when you turn your HDS8 on by connecting the yellow wires together or you can connect the yellow wire to a switch to power the StructureScan. Use a pencil to mark the LSS-1 mount-ing holes.

None of the ground pins are needed to get SI work. Turning off the HDS turns off the LSS-1. Mike Gofron shows the installation of a Lowrance HDS10 and HDS8 with structure scan.

Structure scan is turned on in the hds 8. I couldnt get any wiring diagram or pin layout for the LSS-2 but some simple tests were all that was needed. Page 1 manual simrad structurescan lowrance lss 1 structurescan manual lss- 1 sonar module english lowrance lss 1 structurescan manual www.

Networking 2 LSS-1 Units for StructureScanDownScan on Bow and Stern Here is the diagram how to wire two LSS-1 units together so you can enjoy front side scanningdownscan with transom sidescanningdownscan. Place the LSS-1 into the desired mounting location where the connectors will be easily accessible.