Bently Nevada Proximitor Wiring Diagram

Connect the field wiring to the new IO module. Capacitance values for the field wiring provided by GE for use with Bently Nevada transducers are shown in Table 1.

Bently Nevada Proximitor Wiring Diagram - If you're searching for video and picture information related to the key word you have come to pay a visit to the right site. Our site gives you hints for seeing the maximum quality video and image content, search and find more enlightening video content and graphics that fit your interests. includes one of tens of thousands of movie collections from several sources, especially Youtube, so we recommend this video that you see. This site is for them to stop by this site.

Https Www Amet Co Th Wp Content Uploads 2019 05 Dx791 Pdf

508 mm 2 in Recommended minimum.

Bently nevada proximitor wiring diagram. On the Bently Nevada DVD. Install the new IO module into the rack. The wiring instructions assume that the interconnect cable is the standard Bently Nevada cable part number 16925 - XX.

Hold Alarm set points Alert Danger Compare monitored values with Alarm set points. Consult Performance Specification 155687 for signal rolloff at high frequencies when using longer field wiring lengths or external safety barriers located some distance from the monitoring system. The output of the proximitor is a voltage varying directly as the distance between the probe and the observed surface varies.

Sensors included in this proximitor series are. Wiring instructions for the appropriate monitoring system below. The GE Bently Nevada 3300 XL 8mm Proximity Transducer System consists of one 3300 XL 8mm probe one 3300 XL extension cable and one 3300 XL Proximitor Sensor.

The proximitor is the amplifying unit that conditions the electrical energy supplied to the probe and adjust or laniaries the return signal to a standard of 200 mvmil. MONITOR - FAN ASSY WITH INTEGRAL POWER SUPPLY AND 4-CHANNEL VIBRATION MONITOR PARTNO. The 3300 XL 11 mm Proximity Transducer is designed for measuring position or vibration within a frequency range of 0 to 8 kHz.

Linear Range 2 mm 80 mils. 3300 XL 8 mm Proximity Transducer System. Linear range begins at approximately 025 mm.

Maximum length of 305 metres 1000 feet between the 3300 XL Proximitor Sensor and the monitor. 3300 MONITORING SYSTEM Connect the cable A lead to the IN terminal on the monitor the B lead to. 350040 Proximitor Monitor Four Channel Monitor Accepts input from proximity transducers Monitors Radial Vibration and Thrust Position Vibration 0- 500μm or 0- 20 mil Max.

Procedures and diagrams for setting up network and remote communications 3500 Field Wiring Diagram Package 130432-01 diagrams that show how to hook up a particular transducer lists of recommended wiring Notice. The system can directly accept selected proximity probe types without the need for an external Proximitor sensor. Document Number Description 130432 3500 System Field Wiring Diagrams 141706 3500 Galvanic Isolator Interface 129766 3500 Monitoring System Rack Weatherproof Housing 136275 350008 Diagnostics Access Panel 129767 350015 AC and DC Power Supplies.

Remove the old IO module from the rack. BENTLY NEVADA Bently Nevada 990 Vibration Transmitter Provides a 4-20 mA signal proportional to relative vibration on smaller non-critical machinery Bently Nevada TK-3 Proximity System Test Kit Simulates shaft vibration and position for calibrating GE Bently Nevada monitors and proximity probes Bently Nevada. Typical applications of this system include radial vibration and position axial position and Keyphasor measurements.

Reduces wiring and installation costs and allows you to mount the system on the. Calibration to other target materials is available upon request. This manual does not contain all the information required to operate and maintain the ProximitorSeismic Monitor.

762 mm 3 in When gapped at the center of the linear range the interaction between two separate transducer systems cross-talk will be less than 50 mV on shaft diameters of at least 50 mm 2 in or greater. Superior performance in harsh environments. When using cable from another supplier consult their datasheet or contact the manufacturer to obtain capacitive values.

You can search for a document using its number or description. The system provides an output voltage that is directly proportional to the distance between the probe tip and the observed conductive surface and can measure both static position and dynamic vibration values. See the frequency response graphs in through Figure 13 pages 27 and 28 for signal rolloff at high frequencies when using longer field wiring lengths.

Remove the field wiring from the IO module. The appropriate network adaptor permits single-cable. 350040M Proximitor Monitor Bently Nevada Asset Condition Monitoring Description The 350040M Proximitor Monitor is a 4-channel monitor that accepts input from Bently Nevada proximity transducers conditions the signal to provide various vibration and position measurements and compares the conditioned signals with user-programmable alarms.

Channels 1 and 2 ca. 152 mm 06 in diameter flat target. Bently Nevada Asset Condition Monitoring 350042M Proximitor Seismic Monitor.

3300 XL 11 mm Proximity Transducer System. The 350042M ProximitorSeismic Monitor is a 4-channel monitor that accepts input from proximity and seismic transducers conditions the signal to provide. Consult Bently Nevada Applications Note Considerations when using Eddy Current Proximity Probes for.

When this is not possible or practical it will be necessary to determine these values yourself. 305 metres 1000 feet maximum length between 3300 Proximity Transducer and monitor. Proximitor Sensors are supplied by default from the factory calibrated to AISI 4140 steel.

Best performing and longest lasting proximity sensors on the market today. Bently Nevada Asset Condition Monitoring FieldMonitor Machinery Protection System. The features of the Bently Nevada 3300 XL Series Proximitor Sensors include.

If the wires connected to the IO module are not labeled label the wires before you remove them. Recommend using three-conductor shielded triad cable.